BENDIX BRSM0890 Instrukcja Użytkownika Strona 1

For the most current information, visit the Roadranger web site at www.roadranger.com16.5" Series S-Cam CastXTRALIFE TM P-SeriesXTRALIFE II TM

8PREPARATION1.1.1.1.1. Park vehicle on a level surface and preventmovement by means other than the brakes.2.2.2.2.2. If equipped with spring brakes, c

Standard Chamber Long Stroke Chamber Rated Stroke Max Readjust Stroke Rated Stroke Max Readjust Stroke12 1.75

10PREVENTATIVE MAINTENANCEAAAAAA.A.A.A.A. Released PositionB. B. B. B. B. Applied PostionBBBBBMEASURING PUSH ROD STROKE1.1.1.1.1. Measure the dista

BRAKE DISASSEMBLYCAST SHOE & "P" SERIES1.1.1.1.1. Insert sturdy lever between end of shoe and spider.Pry shoe away from cam until cam r

AIR CHAMBER BRACKET ASSEMBLYINSPECTION OF PARTSSPIDER REMOVAL1.1.1.1.1. Mark the postion of the spider on the axle (L.H. orR.H.) and the orientation o

SHOES AND LININGSTANDARD, XL, XL II AND P SERIES1.1.1.1.1. Check shoes for bent shoe ribs, cracks in shoetable welds or ribs, and elongated rivet hole

INSPECTION OF PARTS (CONTINUED)14FFFFFigurigurigurigurigure 1e 1e 1e 1e 100000TRANSIT BRAKE (CAST SHOE ONLY) DRUM/LINING CROSS REFERENCE CHART1.1.1.1.

CA CA CA CA CAUTION:UTION:UTION:UTION:UTION: Left Hand and Right Hand does notestablish which side of the vehicle the cam goes on. Leftand r

BRAKE SHOE ASSEMBLYSTANDARD, XL & XL II SERIES1.1.1.1.1. Install new return spring pins:A. StA. StA. StA. StA. Standarandarandarandarandard Serie

BRAKE ASSEMBLY (CONTINUED)17FFFFFigurigurigurigurigure 1e 1e 1e 1e 144444“P” SERIES11111. Install new return spring pins. See FSee FSee FSee FSee Fig

4.4.4.4.4. Grabbing or pulling.A.A.A.A.A. Grease, oil, or dirt on linings.B.B.B.B.B. Glazed linings.C.C.C.C.C. Brake linings not a balanced set,differ

195.5.5.5.5. Wear on edge oflining.A.A.A.A.A. Wrong width lining.B.B.B.B.B. Holes improperly drilled in lining.C.C.C.C.C. Wrong drum, or improperly ma

20SYMPTOM CAUSE REMEDYBRAKE DRUM TROUBLESHOOTING CHARTA.A.A.A.A. Turn, per manufacturer’s specifications.B.B.B.B.B. Inspect wheel and drum and replac

21RELINE PROCEDUREThe installation should be checked by attempting toinsert a .006" feeler gage between the lining and shoetable. It should not

RELINE PROCEDURE1359711264128101710298563191218161420114131517Bolting ApplicationUse 3/8 inch diameter copper alloy bolts.Torque bolts to 15-17 Lb-Ft

BRSM-089005/04 PDFPrinted in USAThe Roadranger® System is an unbeatable combination of the bestproducts from Eaton and Dana -- partnering to provide y

TABLE OF CONTENTSiGENUINE SPICER SERVICE PARTSShould a brake assembly require replacement component parts, it is recommended that SpicerBrake Service

97 170 IDENTIFICATION2The brake assembly may be identified by a tag which islocated on the camshaft bracket cylinder, near thegrease fitting.The mylar

BRAKE COMPONENTSSTANDARD/ XTRALIFE 16.5"3Retaining RingCamshaft AdjustingWashers (Shims)Grease FittingAir ChamberBracket AssemblyGrease SealSteel

BRAKE COMPONENTS16.5" CAST SHOE SERIESRetaining RingCamshaft AdjustingWashers (Shims)Grease FittingAir ChamberBracket AssemblyGrease SealSteel Sp

BRAKE COMPONENTS16.5" XL II SERIES BRAKERetaining RingCamshaft Adjusting WasherSteel SpacerGrease SealCamshaft BushingCamshaft BracketCamshaft Bu

BRAKE COMPONENTS16.5" P SERIES BRAKERetainer RingCamshaft Adjusting WasherSteel SpacerGrease SealCamshaft BushingCamshaft BracketCamshaft Bushing

7GENERAL PRECAUTIONSAll Spicer original equipment or service parts forsteering and drive axle brakes are manufactured usingnon-asbestos brake lining.